Reproduction & Aftermarket XR75 XR80 XL75 Parts

Replica chrome steel front brake cable clip. p/n 45469-116-000. Found on left fork lower of 1973-75 XR75, 1974-75 MR50, 1974 XL100 and XL125. Uses 6 x 12 hex bolt and 6mm flat washer to secure to fork. (Hardware not included)

$9.95 - NEW!

Bracket stays. Semi circle stay wraps around fork leg to secure front plate bracket. Painted black. p/n 64115-116-670B for use with 64114-116-670B

19.95 set

HONDA Replacement inner and outer cable guide for model years '73 - early '74 where brake cable runs behind front plate.

$13.95

RE-MX Replacement front number plate for 1974-75 MR50, 1974-78 XR75 and 1979 - 1987 Z50R, 1986 Z50RD - Tahitian red, yellow, ceramic white or bright white. Don't forget to add the NEW brackets or front plate clips and bands to your order.

$15 per plate

Cable guide P/N 61138-357-000. Included in bracket kit. Correct for MR50, CR125M, CR250M, XR75, and XR80

$5.00 - new lower price!

Front number plate bracket kit for MR50, XR75, XR80. Comes with everything shown - correct 5mm hardware, cable guide, replica bracket, and O-ring strap. P/N 64110-131-000

$23.95

Original style number plate stay. Included in bracket kit. 64111-131-000

$13.95

Front Plate kit complete with bracket, cable guide and correct band. All the right pieces at the right price. This is a combination of bracket kit, correct band and oval number plate for the 1974-75 MR50 and 1977-78 XR75. If your bike has no front plate this is exactly what you need.

$44.95

RE-MX Replacement set of three (3) plates for Z50R, Z50RD MR50, XR75 - Tahitian red, yellow, ceramic white or bright white. Don't forget to add the NEW brackets or front plate clips and bands to your order. This is for 3 of the same color plate at a reduced price.

$39 per set of 3

NEW! Replacement chrome cable guide for XR75 73-76 and CB125S 1981-82 CB125S1 S2. Mounts between the handlebar risers. Replaces Honda part number 53139-107-721. Chrome finish.

$11.95

Lever set with rubber tip - Fits SL70, XL70, XR75, Late model CT90, SL100, SL125, CB350, SL350, CB360, XL250, CR125/CR250M and many other models that use p/n 53175-369-700 and 53178-369-700

$15.95

Two wire, push button kill switch will work for almost all the Honda dirt bike models.

$12

All Balls tapered steering bearings. Drop-in replacement to upgrade from OEM ball-type bearings to taper bearings. Comes with seal (not shown)

$40

Fork seals fit SL70, XL70, 1973 XR75 - 1983 XR80, XL75, model. See these fork seals for genuine Honda parts.

$9.95 set

Chrome or Black handlebars for 1973-1976 and 1977-1982. These fit ONLY XR75 and XR80 models. These are not the same as XL75 or XL80 models.

$101.00 chrome

$79 black

After market lever bracket with black finish. Perfect replacement for XR75, TL125, XL70, SL125 and CR125. Same casting as the Honda but obviously not the price that Honda charges. Choose left or right (shown).

$12.95

Re-MX exclusive! Replacement red grip set for 1978 XR75, 1977/1978 CR125. Replaces Honda part number 53165-400-770ZA, 53166-400-770ZA.
I got my order this weekend and the red XR75 grips are awesome. I think they are underpriced. - Brian in Indiana

$45.00

3 position kill switch MR50/XR75. Will mount left side on later XR75/XR80 but you must modify it yourself

BE BACK SOON!

NGK spark plug cap - XR75, XR80, TL125, TL250 and more.

$4.00

Aftermarket spark plug cap for Z50, Z50R, MR50, QA50, CT70 to 1978, SL70 K0-K1, XL70 up to 1976, and all XR75/XR80 and XL75/XL80 models. No marking so it looks like the original. Included with the replacement coil.

$5.75

NEW! Replacement wire harness for 1973-76 Honda XR75. Replaces Honda part number 32100-116-670.

$21.95

Replacement 6V coil with spark plug cap. Made by the same company as the original coil. Use your existing bracket and screws. Detailed instructions coming soon. Tested on '73-76 XR75.

$61.95

Replacement 6V coil with spark plug cap. Made by the same company as the original coil. Use your existing bracket and screws. Tested on XL75 1977-1979 or XL80S 1981-1982 only.

$61.95

PVL ignitions for your favorite XR.

$499

Plastic front fender. Replaces Honda P/N 61100-116-670QN, 61100-116-710EC. Grey rear is out of stock. Will not fit the '77-78 XR75 or '79 on up XR80

$50.00

Plastic rear fender. Replaces Honda P/N 80100-116-671QN, 80100-116-710EC Grey rear is out of stock. Will not fit the '77-78 XR75 or '79 on up XR80

$45.00

XR75/XR80 PRE-84 UNIVERSAL 1.2 gal. plastic replacement gas tank. All necessary hardware included. Will need to drill through frame gusset on some model years.

$219.00

Complete Keyster carburetor repair kit for XR75 and 1979 XR80. Needle, seat, pilot jet, main jet, screws. XR80 and XL80 sets available too.

$25.95

Just need the rubber gaskets for your carburetor? You can find them here

Replacement carburetor to air box boot (tube) Honda p/n 17253-116-670. Made from NOS part and it is perfect! Fits 1973-1976 XR75 just need to use your garter spring and original clamp.

$45.95

After market chrome open-style air filter with band. Fits 20mm carburetor.

$12.95

Motorcycle Fuel Tank repair kit by POR15. This is the fuel tank system we use in our restorations. Cleans, etches the tank, and seals the rust to prevent any more from forming. Will also seal pinholes in the steel tank. One kit will fix up to a 5 gallon fuel tank. Can not be shipped by air.

$55.95

Heavy Duty Motorcycle Fuel Tank repair kit by POR15. Same as the smaller kit, but it adds stripper so you can remove the KREEM and other inferior sealer that you find before lining it correctly. Cleans, etches the tank, and seals the rust to prevent any more from forming. Will also seal pinholes in the steel tank. One kit will fix up to a 5 gallon fuel tank. Can not be shipped by air.

$61.95

Universal inline fuel filter for all standard gasoline fuels - will not be harmed by E85 gasolines

$3.95

XR75 1976 - 1978, '79-'84 XR80 replacement 20mm carburetor. Will not easily mate to early XR intake.

$65.00

NEW! Replacement jet kit fits XR75/XR80 carburetor. Stock jet is #89. Kit includes #82, #85, #87, #90, #92, #95

$10

6 volt battery XL75, XL80, XL100, XL100S, XL125

$31.95

NGK spark plug. See your owner's manual for gap size.

$2.95

Tune-up kit (points, condensor, plug)

$18.95

Points, breaker contact. Fits XR75/K1-’78
XL75 ‘79
XR80 ‘79-’83
XL80S ‘80-’83

$8.95

Condensor for XR75/K1/K3/76-78
XL75/77-79
XL80S 80-83

$7.95

Clutch cover gasket for XR75 1973-1976, 1977-78 XL75/XR75/XL80 or 1979-present XL80, XL100, XR80, XR100, CRF80, CRF100.

$10

Seat foam. Made in the USA using injection molded process for correct fit. See seat covers further down the page.

$53.95

Heavy duty continuous cam chain for XR75/XR80. No master link. THIS IS NOT A FINAL DRIVE CHAIN! Available in 86L for XR75 73-76, XL75 77-79, CT90 66-79 and SL90 69. And 88L fits XL80S 80-85 or XR80 79-84

$18.95

16 pc. gasket set including the all important exhaust gasket. '73-'76 XR75. No left side cover gasket.

$31.95

10 pc. top end gasket set including O-rings, valve seals, gaskets.
'77-'79 XL75
'77-78 XR75
'79-85 XR/XL80S
'85-88, 90-91 XR80R

$25.95

18 pc. gasket set including the all gaskets shown here. For
'77-'79 XL75
'77-78 XR75
'79-85 XR/XL80S
'85-88, 90-91 XR80R

$42.95

XR75 ALL MODEL YEARS Clutch kit complete with steel, fiber and springs. These will not fit XL75/XL80

$49.95

XR75 ALL MODEL YEARS Clutch springs - set of 4. These will not fit XL75/XL80

$15 per set

K0-'76 XR75 exact replica, steel side number plate kit.
2 color matched urethane painted plates, 4 rubber grommets, 2 Honda bolts and washers, 1 correct decal set.

OUT OF STOCK

K0-'76 XR75 exact replica, steel side number plate. Painted - no decals, rubber or hardware
2 color matched urethane painted plates.

OUT OF STOCK

Seat cover fits XR80. Made in the USA of rough grain material with with side and rear logo.

$69.95

Self-adhesive seat pan edge protector. Keeps sharp pan from cutting new fabric. Same as original.

$6.50

Seat cover fits XR75/XR80. Made in the USA of rough grain material with "HONDA" logo on back.

$49.00

Seat cover fits 1980-81 CR80. Choose model year. Made in the USA of rough grain material with with side and rear logo as shown.

$69.95

Seat stencil CR 80R logo for seat sides of your 1980 CR80 cover as shown at left. You will need vinyl paint and a steady hand. Our covers have a logo on both sides!

$14.00

Seat stencil HONDA logo for seat back of your cover. You will need vinyl paint and a steady hand. Ours has a logo!

$5.00

1973-76 muffler mounting bracket. Stay, muffler mount. Replaces Honda p/n 18340-116-670CT.

$35

1973-76 XR75, replacement collar, exhaust pipe joint. These are the spacers needed to mount stock flange to OE exhaust pipe or our pipe. Replaces p/n 18233-115-010.

$18 set

1973-76 muffler drain and spark cover screw set. Low profile 6mm screws to secure lid (spark arrestor cover) and plug drain opening. Set of 3 with washers.

$3.50

Click to see larger image.

K0-'76 XR75 replacement muffler. Excellent fitting replacement muffler comes with spark arrestor cover and lid gasket too. Mounting bracket, exhaust gasket, collars and hardware sold separately. Replaces Honda p/n 18300-116-677. This is meant for those replacing an existing muffler as it does NOT come with mounting bracket. LIMITED QUANTITY

$429

1977-79 XL75 replacement mufffler. This is not 100% OEM specification, just a solid replacement. Heat shields are not included.

$299

Twin Shock 1979-83 XR80, Twin shock XL100(1981 only) replacement muffler. This is not 100% OEM specification, just a solid replacement.

$299

Chain break tool for 420 to 630 pitch standard chain. For use with all brands of motorcycle chain.

$19

Chain and sprockets for your XR75 or early XR80 to 1979. These are stock size 14T front and choose 44T or 46T rear sprocket and high quality 100 link 420 chain. Buy the set and save.

$49.95

Drive chain 100 link. (may need to be cut to length)

$16.95

100L 420 pitch gold drive chain. Tensile strength for bikes up to 80cc.

$26.95

Front sprocket. Counter sprocket in 12T - 15T

$10.95

Closest match to original 44T rear sprocket (early XR) OR 46T rear sprocket (later XR). Fits XR75 from 1973-84.

$29.95

46T steel rear sprocket 420 pitch for XR80R from 1985 to 2003.

$29.95

110L 420 pitch drive chain with master link. Tensile strength for bikes up to 80cc. Needed on modified swing arm bike and XR80R after 1984.

$17.95

Aluminum rear sprocket. Fits XR75, XR80 to 1984, XL80S. Stock size 44T or 46T. Available in many sizes.

$59.00

Aluminum rear sprocket w/ alternating size holes. Fits XR75, XR80 to 1984, XL80S. Stock size 44T or 46T. Available in many sizes.

$65.00

Reproducton chain guide replaces Honda p/n 52156-074-000. Used on 1973-78 XR75, 1979 XR80, SL90, SL100, XL100 1974-76, SL125.

$15.95

50mm snap ring that secures the sprocket to the hub.

$1.50

Replacement rear shocks - sold as a set. Slightly narrower at the top mount. Shim with washers or use your top eye. Also the same as K2-76 XR75 models except springs are chrome - not black. Will not fit '77-78 XR75 or any XR80 models

High quality brake shoes for front or rear. XR75 1973-78, SL70 1971-1973, XL70 '74-76, QA50, CT70, Z50 (some), '79 Z50R. They even come with new springs!

$10.00 - SALE!

Japanese, high quality brake shoes for front or rear. XL75 '77-79, XL80S '79-85, XR80 '79-'84, XR100 '81-'84, XR200, CR125 '74-'78, CR80 80-'82, MR175, MT125

$17.95

A good trials tread tire for the SL70/XL70 and XL75 XL80 models. 3 x 14 inch rear tire.

$84.95

A good trials tread tire for the SL70/XL70 and XL75 XL80 models. 2.5 x 16 inch front tire.

$72.95

2.5 X 16" front tire or 3.6" X 14 rear tire. Original tire found on XR75/XR80 from 1977- present. Look great on early XR75 and modified bikes!

$55.00

3 x 25 split pin. Fits rear axle MR50, front and rear of almost all other minis including XR, XL, SL, CT, CR125. Brake pivot on some bikes.

$0.35

16" or 14" rim strip

$2.00

2.25/2.5 X 16" front tube
3.0/3.6" X 14" rear tube

$9.95